manualshive.com logo in svg

Videx 380N/UK, Installation And Programming Manual, Page: 18 / 28

Share
Download
Videx 380N/UK Installation And Programming Manual Download Page 18

66250010-EN - V2.0 - 24/09/18 

- 18 -

Telephone Interface Module

Art. 380N/UK Telephone Interface Module - Installation Instructions

User Commands

USER COMMAND TABLE

The following user command table shows the user commands that can be used to activate the functions of the 

Art.380N/UK

. If the 4 

digit access code facility is active, this will be required before the command will work e.g. if the 4 digit access code is 

‘4321’

 the user 

would press the following to open the speech to the door panel without first being called 

** 4321 7

.

KEY BUTTON TO PRESS (COMMAND)

FUNCTION

Either 0, 8 or 9

(depending on programming)

Open the door during the call.

1

During dial in mode, pressing button 

1

 will enable the divert facility.

2

Press button 

2

 during dial in mode to open the speech to the door panel. Also press 

button 

2

 after answering a call in divert mode to open the speech to the door panel 

(when this mode is active i.e. 

**361

).

5

Activate auxiliary output 

A1.

6

Activate auxiliary output 

A2

 (only when auxiliary 

A2

 has been set to direct control).

0

Connect to telephone line (

PABX

 mode only).

**7

Open speech to door without first being called and switch between calls.

7

During divert mode it will end the call and switch 

OFF

 the door panel (recommended 

way to end a diverted call).

#

Clear to start again if a mistake is made when typing code in divert mode.

USER COMMAND EXAMPLES

The following examples show what key buttons to press on the telephone (examples based on default settings):

•  To open the speech to the door panel without first being called: 

 

 

 

**7

•  To divert to a door call while talking with someone on the telephone:   

 

 

**7

(NOTE: to go back to the telephone call simply hang up the handset and pick up again)

•  To divert to a telephone call while talking with someone at the door panel: 

 

 

**7

(NOTE: to go back to the door call simply hang up the handset and pick up again)

•  To open the door without first being called:   

 

 

 

 

 

**0

•  To 

open 

the 

door 

during 

a 

call: 

       0

•  To 

put 

the 

system 

in 

divert 

mode: 

       **111

•  To take the system back out of divert mode:   

 

 

 

 

 

**110

•  To activate auxiliary A1 without first being called: 

 

 

 

 

 

**5

•  To activate auxiliary A2 without first being called: 

 

 

 

 

 

**6

•  To 

activate 

auxiliary 

A1 

during 

a 

call: 

       5

•  To 

activate 

auxiliary 

A2 

during 

a 

call: 

       6

•  To activate the speech when dialling into the system:  

 

 

 

 

2

•  To activate the speech in divert mode (when setting **361 is set): 

 

 

 

2

Summary of Contents for 380N/UK





























Reviews:

No comments