manualshive.com logo in svg

Videx 380N/UK, Installation And Programming Manual, Page: 16 / 28

Share
Download
Videx 380N/UK Installation And Programming Manual Download Page 16

66250010-EN - V2.0 - 24/09/18 

- 16 -

Telephone Interface Module

Art. 380N/UK Telephone Interface Module - Installation Instructions

Programming the Art.380N/UK

AUTOMATICALLY OPEN SPEECH WHEN ANSWERING A DIVERT CALL

When this mode is set to 1 it will be necessary for the user to press 

2 on the telephone after answering a call that has been diverted 

to it. This feature disables the door entry panel amplifier until 2 

is pressed on the telephone so that no dialling tones are heard 

and the caller is not aware that the initial call is being diverted.

Code

Mode

36 1

Must press 2 to open speech

36 0

Speech opens automatically (default)

Example 1:

 A call diverted to a mobile phone when 

**36 1

 is set (enabled) -

1. The mobile phone will ring (no sound will be heard from the door panel speaker) and the caller display will show 

that it is from the telephone number attached to the 

Art.380N/UK

 (if the caller ID is enabled on the telephone);

2. The user answers the call and no sound will be heard;
3. The user then presses button 2 on the mobile phone to open speech to the door panel.

Example 2:

 A call diverted to a mobile phone when 

**36 0

 is set (disabled) - 

1. The mobile phone will ring (this will also be heard through the speaker at the door panel as well);
2. The user answers the call and speech will be open automatically.

To set this mode use one of the following codes shown in the table above. By default this feature is disabled (set to 0).

ACCESS CODE SETUP

The 4 digit access code is used to restrict access to the programming menu and commands. It can be disabled, setup for both local 

calls and diverted calls or setup for just diverted calls.

EDIT OR DELETE THE ACCESS CODE

This programming command allows the user to edit an existing 

4 digit access code (if known) or delete the access code.
Use one of the following codes shown in the table to setup or 

delete the access code (where 

XXXX

 = the 4 digit code required).

Code

Mode

31 XXXX

Change the code to XXXX

31 1111

Delete the code

ENABLE / DISABLE THE 4 DIGIT ACCESS CODE FOR LOCAL CALLS

This programming command allows the user to enable or disable 

the 4 digit access code for local calls. By default this feature is 

disabled. Use one of the following codes shown in the table to 

enable or disable the access code.

Code

Access Code Status

20 0

4 digit code enabled

20 1

 4 digit code disabled (default)

SPECIALISED SETUP

The following options can be adjusted for specialised situations. For standard installations these settings will not normally need to 

be adjusted.

PULSE MODE

The pulse mode facility can be used with older pulse style 

telephones that cannot generate 

DTMF

 dial tones.

Use one of the following codes shown in the table to enable or 

disable pulse mode.

Code

Pulse Mode

13 0

Disabled (default)

13 1

Enabled

PABX MODE

PABX 

mode can be used on systems which do not have a 

telephone line or have a telephone line but needs to be isolated 

from it. When this is enabled it will be necessary to press 

0

 on the 

telephone. to select the telephone line before dialing a number.

Code

PABX Mode

14 0

Disabled (default)

14 1

Enabled

Use one of the following codes shown in the table above to enable or disable 

PABX

 mode.

IMPORTANT NOTE: The Art.380N/UK can also be put into PABX mode following the 'hard-wired' reset procedure described on 

page 13. Remember that this method will also reset the Art.380N/UK back to factory defaults so any programming made prior to 

the reset will need to be re-programmed again.

Summary of Contents for 380N/UK





























Reviews:

No comments