
66250010-EN - V2.0 - 24/09/18
- 14 -
Telephone Interface Module
Art. 380N/UK Telephone Interface Module - Installation Instructions
Programming the Art.380N/UK
PROGRAMMING COMMANDS AND ADJUSTMENTS
The following adjustments can be used to program the system to the user's requirements. Remember after picking up the telephone
handset to press
** 371
on the handset keypad to unlock the programming commands and listen for the double tone confirmation
beep.
ADJUST THE NUMBER OF RINGS
The
Art.380N/UK
can be programmed to ring the telephone(s)
for as little as 1 ring or for a maximum of 10 rings, using one of
the following codes shown in the table.
By default this is set to 6 rings.
Code
Rings
Code
Rings
21 1
1
21 6
6 (default)
21 2
2
21 7
7
21 3
3
21 8
8
21 4
4
21 9
9
21 5
5
21 0
10
ADJUST THE DOOR OPEN TIME
The
Art.380N/UK
can be programmed to release the door for as
little as 1 second or for a maximum of 18 seconds, using one of
the following codes shown in the table.
By default this is set to 6 seconds.
Code
Time (secs)
Code
Time (secs)
22 0
1
22 5
10
22 1
2
22 6
12
22 2
4
22 7
14
22 3
6 (default)
22 8
16
22 4
8
22 9
18
ONBOARD RELAY REVERSAL (C/NO OR C/NC)
The relay contacts of the
Art.380N/UK
can be programmed to
either be normally open going closed (C/NO, default position)
or programmed to be normally closed going open (C/NC), using
one of the following codes shown in the table.
Code
Status
Code
Status
10 1
NC
10 0
NO (default)
CHANGING THE DOOR OPEN BUTTON (0, 8 OR 9)
The door open button on the telephone handset is button
0
(default) however this can be changed to either button
8
or
button
9
, using one of the following codes shown in the table.
Code
Button
Code
Button
23 0
0 (default)
23 5
8
23 1
9
SETTING UP THE AUXILIARY OUTPUTS (A1 AND A2)
There are two auxiliary outputs available on the
Art/380N/UK
,
A1
and
A2
. These outputs are a switch
0V
(open collector, 200mA
max.) signal which can be used for a number of facilities including activating additional dry contact relays. The outputs can be set
to latch on activation or switch momentarily (default).
To setup the auxiliary outputs
A1
and
A2
use one of the following
codes shown in the table. By default both outputs are set to
1
,
momentary trigger.
Code
Output
Code
Output
28 0
A1 latching
28 1
A1 momentary
29 0
A2 latching
29 1
A2 momentary
USING THE AUXILIARY OUTPUTS
• To activate auxiliary output
A1
during a call simply press button
5
on the telephone. If the auxiliary output is set to latch then
it will be necessary to press button
5
again to unlatch the output.
• To activate auxiliary output
A1
without a call being in progress simply pick up the telephone handset and press the buttons
** 5
on the telephone. If the output is set to latch, follow the same procedure to unlatch.
• To activate auxiliary output
A2
during a call simply press button
6
on the telephone. If the auxiliary output is set to latch then
it will be necessary to press button
6
again to unlatch the output.
• To activate auxiliary output
A2
without a call being in progress simply pick up the telephone handset and press the buttons
** 6
on the telephone. If the output is set to latch, follow the same procedure to unlatch.
Additionally, auxiliary output
A2
can be programmed to
automatically activate when a call is placed.
IMPORTANT NOTE: If A2 is set to activate automatically it cannot
also be set to latch as indicated above.
Code
Output
Code
Output
19 0
Automatic
19 1
Manual