manualshive.com logo in svg

Videx 380N/UK, Installation And Programming Manual, Page: 11 / 28

Share
Download
Videx 380N/UK Installation And Programming Manual Download Page 11

66250010-EN - V2.0 - 24/09/18 

11

Telephone Interface Module

Art. 380N/UK Telephone Interface Module - Installation Instructions

•  That the all-pole circuit breaker shall be placed in such a way to allow for easy access and the switch shall remain readily 

operable.

•  Ensuring that the mains supply (Voltage, Frequency and Phase) complies with the product rating label.
•  Isolating the mains before carrying out any maintenance work on the system.

FUSE

N

L

Mains

1 PHASE SUPPLY

(220 - 240Vac, 50/60Hz)

SWITCHED FUSE SPUR

Fig. 12

 

POWER SUPPLY INSTALLATION AND MOUNTING

Follow the steps below when fitting the 

Art.380N/UK:

•  First remove the terminal side covers by unscrewing the retaining screws.
•  Fix the 

Art.380N/UK 

to a DIN rail, following 

Fig.13

, 

Fig.14

 and 

Fig.15

, or directly to the wall using 2x rawl plugs and 2x   

expansion type screws, see 

Fig.16

 (2x40mm, Ø3.5mm self-tapping masonry screws and 2x40mm, Ø4mm nylon rawl plugs 

will suffice).

•  Switch OFF the mains using the circuit breaker (mentioned previously) and then make the connections as shown on the 

installation wiring diagrams (refer to pages 19 - 22 for examples).

•  Check the connections and secure the wires into the terminals ensuring that the low voltage (signal) cables are routed 

separately from the high voltage (mains) cables.

•  Replace the terminal covers and fix them back into place using the relevant screws.
•  When all connections are made restore the mains supply.

Fig. 13

 

Fig. 14

 

2x rawl 

plugs

2x expansion

type screws

Fig. 15

 

Fig. 16

 

General Directions for Installation

Summary of Contents for 380N/UK





























Reviews:

No comments