Victron energy MultiPlus Compact 12/1200/50-16 Manual Download Page 71

Page: 71 / 124

www.victronenergy.com

APPENDIX A: Connection overview

A AC input line L1 and neutral (N)

B 2x RJ45 connector for remote panel and/or parallel and 3-phase operation.

C AC output line L1 and neutral (N).

D AC input circuit breaker

F M8 battery minus connection.

G Starter battery positive (TR CHARGE).

(starter battery minus: use battery minus

cable for connection).

H Terminals for (left to right): temperature sensor positive, temperature sensor minus.

M8 battery positive connection.

L Connector for remote switch:

Short right and middle terminal to switch “on”.

Short left and middle terminal to switch to “charger only”.

M DIP switches for set-up mode.

P Programmable relay

Terminals for (left to right):

Multi-functional relay NO - COM - NC

Q Cabinet GND terminal

R PE (ground) terminals

S Indicator Programmable relay

LED illuminates when relay is activated

Summary of Contents for MultiPlus Compact 12/1200/50-16





























































































































Search results

Summary of Contents for MultiPlus Compact 12/1200/50-16

Reviews:

Related manuals for MultiPlus Compact 12/1200/50-16

Brands by name

Popular brands

Victron energy MultiPlus Compact 12/1200/50-16, Manual

Search results

Summary of Contents for MultiPlus Compact 12/1200/50-16

Reviews:

Related manuals for MultiPlus Compact 12/1200/50-16

Brands by name

Popular brands