Victaulic VicFlex AH1 Manual Download Page 118

Page: 118 / 239

Backflow Direct Tamper Switch Recommendation

Install LB Conduit Body

D. Attach

the second ½” close nipple to LB Conduit body to the threaded port that is

located at the 90 degree angle.

E. Attach the LB Conduit body to 90 degree pull elbow and run electrical leads

through the close nipple into the LB Conduit body.

F. Attach to fire alarm panel leads and reinstall the weatherproof cover on the LB

Conduit body.

G. Attach flex conduit to remaining threaded port on LB Conduit body to create a

weatherproof seal.

Page 4 of 4

Note:

The weatherproof cover may need to be removed to run leads through the conduit body. The cover can be removed by using a

Philips head screw driver to remove the screws located on the cover.

Summary of Contents for VicFlex AH1
















































































































































































































































Search results

Summary of Contents for VicFlex AH1

Reviews:

Related manuals for VicFlex AH1

Brands by name

Popular brands

Victaulic VicFlex AH1, Manual

Search results

Summary of Contents for VicFlex AH1

Reviews:

Related manuals for VicFlex AH1

Brands by name

Popular brands