Viavi 87339 Operation Manual Download Page 103

Page: 103 / 198

Testing

5 -4

5.2.3

GPSG-1000 Debug Files

Debug Files:

If the GPSG-1000 encounters a problem during the boot process and is unable to boot up

properly, a debug file may be obtained from the GPSG-1000 and sent to VIAVI Solutions

to assist in determining the cause of the boot issue.
To obtain a copy of the debug files, install a USB memory device into one of the USB

ports on the GPSG-1000. Press the power button to turn on the GPSG-1000. During the

boot process two text files will be created on the USB Memory Device (Fig. 2-5). One file

is called “gps1000rs232.txt”; and the other file is called “gps1000last_rs232.txt”; these

files contain the latest debug files.
Each time the GPSG-1000 is booted with the USB Memory Device installed in one of the

USB ports, the debug files are overwritten with the latest boot information. The

information contained in the debug file is not intended for use by the user. Both files

should be sent to VIAVI Solutions if support is being requested for a boot issue.

Summary of Contents for 87339







































































































































































































Search results

Summary of Contents for 87339

Reviews:

Related manuals for 87339

Brands by name

Popular brands

Viavi 87339, Operation Manual

Search results

Summary of Contents for 87339

Reviews:

Related manuals for 87339

Brands by name

Popular brands