manualshive.com logo in svg

Versitron Web Smart+ SG71070M, User Manual, Page: 99 / 123

Share
Download
Versitron Web Smart+ SG71070M User Manual Download Page 99

93 

SG71070M 

    Revision A3

 

3-4.1.2 ARP Inspection 

 

The section describes how to configure the Dynamic ARP Inspection Table parameters of the 
switch. The Dynamic ARP Inspection Table contains up to 1024 entries, and is sorted first by 
port, then by VLAN ID, then by MAC address, and then by IP address. 

Web Interface 

 

To configure a Dynamic ARP Inspection Table Configuration in the web interface: 

1.

 

Click Monitor, Network, ARP Inspection. 

2.

 

Checked “Auto-refresh”. 

3.

 

Click “Refresh” to refresh the port detailed statistics. 

4.

 

Specify the Start from port, VLAN ID, MAC Address, IP Address, and entries per page.   

 

Figure 3-4.1.2:    The Dynamic ARP Inspection Table 

 

Parameter description: 

 

Port   

Switch Port Number for which the entries are displayed.   

 

VLAN ID   

VLAN-ID in which the ARP traffic is permitted.   

 

MAC Address   

User MAC address of the entry.   

 

IP Address   

User IP address of the entry.   

 

Buttons 

 

Auto-refresh: Check this box to refresh the page automatically. Automatic refresh occurs 
every 3 seconds. 

Refresh: Click to refresh the page. 

 

 

Summary of Contents for Web Smart+ SG71070M




























































































































Reviews:

No comments