manualshive.com logo in svg

Versitron Web Smart+ SG71070M, User Manual, Page: 78 / 123

Share
Download
Versitron Web Smart+ SG71070M User Manual Download Page 78

72 

SG71070M 

    Revision A3

 

Cancel – Click to cancel the changes. 

2-13.7 DSCP Translation   

The section describes how the switch allows you to configure the basic QoS DSCP Translation 
settings for the switch. DSCP translation can be done in Ingress or Egress. 

Web Interface 

 

To configure the DSCP Translation parameters in the web interface: 

1.

 

Click Configuration, QoS, DSCP Translation. 

2.

 

Scroll to set the Ingress Translate and Egress Remap DP0 and Remap DP1 Parameters. 

3.

 

Evoke to enable or disable Classify. 

4.

 

Click the save to save the setting. 

5.

 

If you want to cancel the setting then you need to click the Reset button. It will revert to 
previously saved values. 

 
Figure 2-13.7:    The DSCP Translation

 

 

Parameter description: 

 

DSCP   

Maximum number of supported DSCP values are 64 and valid DSCP value ranges from 0 to 
63.   

 

Translate   

DSCP at Ingress side can be translated to any of (0-63) DSCP values. 

 

Classify   

Click to enable Classification at Ingress side.   

 

DPL   

Actual Drop Precedence Level.   

 

Buttons 

Apply – Click to save changes. 

Reset- Click to undo any changes made locally and revert to previously saved values. 

 

 

Summary of Contents for Web Smart+ SG71070M




























































































































Reviews:

No comments