manualshive.com logo in svg

Versitron Web Smart+ SG71070M, User Manual, Page: 18 / 123

Share
Download
Versitron Web Smart+ SG71070M User Manual Download Page 18

12 

SG71070M 

    Revision A3

 

2-2 Ports Configuration

 

The section describes how to configure the Port detail parameters of the switch. Port configure 
can be used to enable or disable a port, monitor the ports content, or status. 

2-2.1 Ports 

This page displays current port configurations. 

Web Interface 

 

To configure a port in the web interface: 

1.

 

Click Configuration, Ports Configuration, and Ports. 

2.

 

Specify the Speed Configured, Flow Control, Maximum Frame size, Excessive Collision 
mode and Power Control. 

3.

 

Click Apply. 

 

Figure 2-2.1:    The Port Configuration 

 

 

Parameter description: 

 

Port   

This is the logical port number for this row.   

 

Link   

The current link state is displayed graphically. Green indicates the link is up and red indicates 
that it is down.   

 

Current Link Speed   

Provides the current link speed of the port.   

 

Configured Link Speed   

Use the menu to select the port’s speed and duplex mode. If you select Auto, the duplex 
mode and speed will be set by the auto-negotiation process. The port’s maximum capability 
(full duplex and 10 Gbps) will be advertised. Otherwise, your selection will determine the 
port’s duplex mode and transmission rate. The factory default is Auto.     

Summary of Contents for Web Smart+ SG71070M




























































































































Reviews:

No comments