manualshive.com logo in svg

Vernier LabQuest 3, User Manual

Share
Download
Vernier LabQuest 3 User Manual Download Page 8

Getting Started 

 

 

2

 

Vernier Software & Technology

 

Preparing for First-Time Use 

Remove the Protective Battery Tab 

LabQuest ships with the battery in place; however, there is a protective tab covering the battery 
contacts that must be removed. Remove the battery and discard the tab before using LabQuest. 
For assistance on removing the battery, see 

Replacing the Battery in the appendix

. 

Remove the Protective Screen Covering 

Remove and discard the protective screen cover that comes on the unit. This cover is intended to 
prevent damage to the screen during shipping. It is not intended as a protective cover for 
everyday use. 

Charge Overnight 

We recommend charging the battery for at least 12 hours prior to using LabQuest for the first 
time on battery power. To do this, connect the included power adapter to LabQuest and an AC 
power source. 

LabQuest uses a high-quality lithium-ion battery. There is never a need to condition the battery 
by regular full discharge/charge cycles and it is safe to leave the battery charging indefinitely. 
For more details about the battery, see 

Battery Maintenance

 in the appendix 

Powering on LabQuest 

 

Press the power button located on the top edge of the unit. LabQuest completes its booting 
procedure and automatically launches the LabQuest App. This can take 45 seconds to complete. 

If the screen momentarily shows a charge battery icon or does not light after a moment, check to 
be sure you have removed the protective battery tab and properly replaced the battery. Connect 
the power adapter to LabQuest and to an AC power source, and then try the power button again. 

Power Button Behavior 

Power on/resume

—If the screen is off for any reason (LabQuest is shutdown, suspended, or the 

screen is off to conserve battery power), press and release the power button to turn LabQuest on. 

 

If only the screen is powered off, pressing the power button turns the screen on. 

 

If LabQuest is suspended, it takes a few seconds for the LabQuest App to start up. 

 

If LabQuest is shut down, it needs to fully boot, taking about 45 seconds. 
 

Summary of Contents for LabQuest 3










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands