VeEX WiFi Air Expert Series User Manual Download Page 27

Page: 27 / 99

High Noise Level

: Detects APs whose noise level is higher than the Noise Level Threshold as configured in the Setup

menu.

High Utilization

: Detects channels whose utilization level is higher than the Utilization Threshold as configured in the

Setup menu.

Go back to top

Go back to TOC

6.2.5 Interference Auto-Test

The following tests are performed during the Auto-Test Interference Check. Test results are compared with Threshold values

configured in the Setup menu see (

Threshold Configuration

Note:

AP Filter

enabled

(see

AP Filter Setup

), only APs selected in the filter list are tested for interference, but all APs

detected in the Auto-Test scan exceeding the Interferer Signal Level Threshold value are examined as possible sources of

interference.

Only APs whose signal level is greater than the Interferer Signal Level Threshold value are examined as possible sources

of interference for this test. Other APs sharing on the same, overlapping, or adjacent channels, but with a signal level

lower than the threshold value are not considered a source of interference.

Interference Auto-Test Results

Co-channel Interference

: Detects APs configured on the same channel. If this number exceeds the Co-channel

Interference Threshold value configured in the Setup menu, an error or warning is detected.

Adjacent Channel Interference

: Detects APs configured on adjacent/overlapping channels. If this number exceeds the

Adjacent Channel Interference Threshold value setup in the in the Setup menu, an error or warning is detected.

Go back to top

Go back to TOC

6.2.6 Top Talkers Auto-Test

The following tests are performed during the Auto-Test Top Talkers Check. The numbers of Top Talkers reported in these tests

are configured in the Setup menu (

see Threshold Configuration

Top Talkers Auto-Test Results

WiFiAirExpertSeries_eManual_D07-00-120P_Rev A00

Summary of Contents for WiFi Air Expert Series




































































































Search results

Summary of Contents for WiFi Air Expert Series

Reviews:

Related manuals for WiFi Air Expert Series

Brands by name

Popular brands

VeEX WiFi Air Expert Series, User Manual

Search results

Summary of Contents for WiFi Air Expert Series

Reviews:

Related manuals for WiFi Air Expert Series

Brands by name

Popular brands