VeEX VePAL TX300 User Manual Download Page 65

Page: 65 / 421

6.6 Setup: OTN/SONET

Selecting SONET from the General tab

To verify that the Tx and Rx block diagrams are OTN/SONET, verify that SONET is selected from the

SDH/SONET

drop-down

menu under the

General

tab.

Go back to top

Go back to TOC

6.6.1 Transmitter Setup

This section of the manual describes the OTN configuration capabilities. The block diagram of the Tx and Rx structure is

described in

6.0 Setup

Hierarchy

Tapping the

Hierarchy

box opens the Tx Hierarchy Setup screen.

Tx Hierarchy Setup

TX300/e_e-manual_D07-00-033P_RevG00

Summary of Contents for VePAL TX300






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands

VeEX VePAL TX300, User Manual

Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands