manualshive.com logo in svg

VeEX VePAL TX300, User Manual

Share
Download
VeEX VePAL TX300 User Manual Download Page 17

Save

 key: Saves test results in the unit's memory. If the measurement is still running, it will provide a snapshot the moment

the key is pressed. The Save function provides automatic storage with automatic naming and time stamping function. To

process a stored file, please go to 

7.0 Files

 in the 

V300 Common Functions manual

.

History

 key: Resets any blinking LED due to a history condition. For more details on the LED, please go to 

LEDs

.

Help

 key: Brings the user to online help, regardless of the current user interface location of the unit.

Lock 

key: Can be configured to lock the keypad or capture the current screenshot.

Home

 key: Brings the unit to its home menu regardless of its location on the user interface.

Arrow

 key: Moves the cursor in any of the four supported directions (left, right, up, down). The Arrow key works in

conjunction with the Enter and Escape keys.

Enter 

key: Provides an enter sequence to the user interface. It is used in non touch screen operation mode to enter menus

and functions.

Escape

 key: Provides an escape sequence to the user interface. It is used in non touch screen operation mode to escape

menus and functions.

Go back to top

 

Go back to TOC

4.3 Touch Screen Display

The LCD supports touch screen operation. To operate the touch screen, use the stylus located in the top cover to navigate the

menus and tabs. The unit can also be used in a non touch screen mode (i.e., using the Arrow, Enter, and Escape keys to

navigate). The location of the cursor on the screen is indicated by a focus state. The focus state varies depending on the function

or section of the test set. Please observe the following precautions:

Never use excessive pressure on the touch screen as this may damage its functionality.

Never use sharp objects such as a pen, screwdriver, etc., as this may damage the surface.

Clean the surface of the touch screen using a soft cloth and mild detergent only. Do not use alcohol.

Go back to top

 

Go back to TOC

4.4 Battery

The VePAL 300 chassis is equipped with an intelligent Li-ion rechargeable battery pack, which is located in the rear of the unit. The

battery will be partially charged upon delivery, so it is recommended to fully charge the battery before use. Please charge the

battery at room temperature to preserve its life and to obtain maximum charge. The battery is charged during operation, provided

the unit is connected to the AC Mains using the supplied AC adaptor. Removing the battery while the unit is powered on is not

recommended - this may result in damage. Remove the rubber cover on the left side to connect the AC Main adaptor to the unit.

TX300/e_e-manual_D07-00-033P_RevG00

Summary of Contents for VePAL TX300






































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands