VeEX VePAL TX300 User Manual Download Page 218

Page: 218 / 421

Call Type

: Select Voice or 3.1K Audio

Channel
Line

: If the Channel Config is set to 46B+2D or 47B+D in DS1 mode or Dual PRI in E1, the user can choose which line to

use.

Numbering Type:

Unknown, International, National, or Local

Numbering Plan:

Unknown, Telephony, or Private

Dial To:

Tap on the corresponding box and use the alphanumeric keypad to enter the number of the receiving line.

Sub Addr Type:

NSAP or User

Sub Addr

: Tap on the corresponding box and use the alphanumeric keypad to enter a subaddress

Call - Voice Setup

Press the

Call

button to initiate a call to the receiving number. If Prompt was selected for Call Answer in the Setup tab, the unit

receiving the call will ring and the user can press

Answer

Reject

to accept or reject the call.

Call In Progress

Trace: ISDN Protocol Decode

D-Channel Decodes help to verify that a call is successfully established or determine why a call was not completed by examining

the protocol cause values. We can monitor Layer 2 (Q.921) and Layer 3 (Q.931) cause code messages on the D-channel in both

terminate and monitor modes. Layer 2 results give technicians the ability to check link and D-channel status, verify LAPD frames

TX300/e_e-manual_D07-00-033P_RevG00

Summary of Contents for VePAL TX300






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands

VeEX VePAL TX300, User Manual

Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands