VeEX VePAL TX300 User Manual Download Page 279

Page: 279 / 421

Step 6: Reviewing Configuration Settings

After starting the test, the Error Injection button becomes available and the screen displays Quick Test view and the following results

for both ports:

Link Up/Down status

Optical Power in dBm

ARP - Pass/Fail status

PING - Pass/Fail status

Round Trip Delay (RTD) measurement in ms

Throughput - Pass/Fail status

Transmitted Rate

Received Rate

Quick Test View

In case of link or IP related test failure, ViPAG will indicate the possible failure in red text and give instructions on what to check for.

Test Failure

TX300/e_e-manual_D07-00-033P_RevG00

Summary of Contents for VePAL TX300






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands

VeEX VePAL TX300, User Manual

Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands