VeEX VePAL TX300 User Manual Download Page 236

Page: 236 / 421

Send

: Press this button to send the programmed code for the amount of time set in the time out field. The test set will stop

sending the code once time is up.

Go back to top

Go back to TOC

12.3 Round Trip Delay

DS1/3 Round Trip Delay is the same measurement described as the

Round Trip Delay

in SDH/SONET Tools. Please see that

section for more details.

Go back to top

Go back to TOC

12.4 DS1 RX Data

DS1 RX data shows received data and captures the current timeslots.

DS1 Data

Go back to top

Go back to TOC

12.5 DS3 Pulse Mask

TX300/e_e-manual_D07-00-033P_RevG00

Summary of Contents for VePAL TX300






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands

VeEX VePAL TX300, User Manual

Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands