VeEX VePAL TX300 User Manual Download Page 361

Page: 361 / 421

CCM Configuration Parameters

CCM

Enable

: Enable sending Continuity Check messages

Disable

: Disable sending Continuity Check messages

Priority:

802.1p priority in the CCM VLAN Tag

Tx Interval:

Choose from the supported CCM intervals: 1 s, 10 s, 1 min, 10 min.

Link Trace and Loopback Messages

OAM - Service Level OAM (Page 2)

Link Trace Messages (LTM/LTR)

LTM (Link Trace Message) Multicast messages are transmitted on demand to a destination MAC address. All MIPs and destination

MEPs respond with LTR (Link Trace Reply) and forward the LTM on to its destination.

LTM Diagram

TX300/e_e-manual_D07-00-033P_RevG00

Summary of Contents for VePAL TX300






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands

VeEX VePAL TX300, User Manual

Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands