VeEX VePAL TX300 User Manual Download Page 124

Page: 124 / 421

Summary (Page 3)

7.4.2 Errors and Alarms

The Error/Alarm tab brings up several pages showing the errors and alarm status.

Page 1 provides an overview of all the Errors and Alarms applicable to the signal or network under test. The color of the page

tab is normally blue; however, it will turn red when an alarm error condition has been detected or recorded.

The soft LEDs on screen are arranged logically and will depend on signal hierarchy, structure, payload and framing selected. The

soft LEDs have a tricolor function:

Green:

No error or alarm is present

Red:

An error or alarm condition is detected and is currently present

Yellow:

Indicates a history condition. An error or alarm was detected during the measurement interval but it is no longer

present or active

Errors/Alarms (Page 1)

Note:

Tapping the individual soft LED will automatically link directly to the applicable result screen which provides detailed

TX300/e_e-manual_D07-00-033P_RevG00

Summary of Contents for VePAL TX300






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands

VeEX VePAL TX300, User Manual

Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands