VeEX VePAL TX300 User Manual Download Page 143

Page: 143 / 421

Go back to top

Go back to TOC

TCMi:

There are six Tandem Connection Monitoring (TCMi) fields that define the ODU TCM sub-layer, each containing

TTI, BIP-8, BEI/BIAE, BDI, and STAT subfields associated to each TCM level (i=1 to 6).

The STAT subfield is used in the PM and TCMi fields to provide an indication of the presence or absence of

maintenance signals.

TCM1 BEI Type

Go back to top

Go back to TOC

Fault Type and Fault Location (FTFL)

Reporting communication channel field used to create a message spread over a 256-byte multiframe

Provides the ability to send forward and backward path-level fault indications

FTFL Type

TX300/e_e-manual_D07-00-033P_RevG00

Summary of Contents for VePAL TX300






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300

Reviews:

Brands by name

Popular brands

VeEX VePAL TX300, User Manual

Search results

Summary of Contents for VePAL TX300

Reviews:

Brands by name

Popular brands