manualshive.com logo in svg

VDO CONTISYS OBD -, Instruction Manual

Share
Download
VDO CONTISYS OBD - Instruction Manual Download Page 88

FastCheck

86

Peugeot

J1962

106 (1997 on): 

- Under 

dashboard - passenger 
side.

206, 306, 806, Partner 
(1997 on):

 - Under 

dashboard - driver's 
side.

307 (to 2004), 406 (1997 
to 2000), 807:

 - Fascia 

fuse box.

107: 

- To left of steering 

column.

307 (2004 on):

 - Behind 

ashtray in centre 
console.

406 (2000 on): 

- Driver's 

side dashboard (remove 
small plastic cover).

407, 607:

 - Centre 

console compartment.

30-pin 
connector

106 (to 1997): 

- 

Passenger side - below 
dash.

806, Partner (to 1997):

 - 

Driver's side - below 
dashboard. 

406 (to 1997), 605:

 -

Fascia fuse box.

Renault

J1962

Clio: 

- Under ashtray - 

centre console.

Espace: 

- Passenger 

footwell.

Kangoo: 

- Driver 

footwell.

Laguna: 

- Centre 

console - in front of gear 
lever.

Laguna 2: 

- Centre 

console - under ashtray.

Megane: 

- Driver 

footwell.

Safrane: 

- Engine 

compartment - Near side 
front wing.

Scenic: 

- Driver footwell.

CO

N

0019

16

9

1

8

CO

N

002

8

CO

N

0019

16

9

1

8

Summary of Contents for CONTISYS OBD -

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands