manualshive.com logo in svg

VDO CONTISYS OBD -, Instruction Manual

Share
Download
VDO CONTISYS OBD - Instruction Manual Download Page 79

FastCheck

77

For BMW X3 (E83), BMW X5 (E53):

• Start the engine but do NOT start driving.

• Hold down the button (shown in the diagram below) for approximately 5 seconds, 

or until the RPA Warning Lamp glows yellow.

• The Warning Lamp should stay yellow for 5 seconds to indicate that the Reset has 

started.

• Drive off. The Reset will terminate without informing the driver of success. If the 

Reset has not been carried out correctly however the RPA Warning Lamp will glow 
red and the process must be repeated. 

• If the vehicle is stopped while the reset is occurring the reset will be interrupted and 

will be resumed when the vehicle is driven again.

Mini

Run-flat Reset (RPA – Tyre Deflation Detection)

The run-flat system monitors the pressure in the four mounted tyres while the vehicle 
is being driven.

The system will provide an alert whenever the inflation pressure in a tyre drops 
significantly in relation to the pressure of another tyre.

It is necessary to initiate the RPA reset process IMMEDIATELY after every tyre 
pressure correction, after a tyre or wheel change or after a trailer has been attached 
or detached. The reset MUST be started before driving the vehicle for the first time 
after one of the above events.

When a reset is required (due to a pressure change in one of the tyres) the vehicle will 
inform the driver by turning on the RPA Warning Lamp, which will glow red, and 
sounding an acoustic signal.

OM1345

Summary of Contents for CONTISYS OBD -

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands