manualshive.com logo in svg

VDO CONTISYS OBD -, Instruction Manual

Share
Download
VDO CONTISYS OBD - Instruction Manual Download Page 56

FastCheck

54

Use the 

 and 

 keys to select the 'FastCheck Service' application and press 

 

to confirm the selection. To return to the previous menu, press the 

 key.

Turn the vehicle's ignition ON.

Use the 

 and 

 keys to select the vehicle manufacturer and press 

 to confirm 

the selection.

Dependent upon the vehicle manufacturer and model different menu options will then 
be available.

Alfa Romeo/Fiat/Lancia vehicles

There are potentially three options in the FastCheck Service menu for these 
manufacturers:

Service Interval

This option resets the conventional service interval indicator. This function is to be 
used AFTER a full service (18000 miles for petrol or 21000 miles for diesel) has been 
completed on the vehicle.

Note

: The Multiplexer cable (A2C59512985) or CAN converter (A2C59512664) 

harness must be used for any diagnostics on the following vehicles:

Alfa-Romeo MiTo

Fiat 500

Fiat Grande Punto (05)

All other vehicles require the Multiplexer cable (A2C59512985) or FAL LS CAN 
(A2C59512070) harness.

Oil Change Reset

This option is currently only applicable to the new Fiat Ducato van (Ducato III MY2006 
onwards). This function is to be used AFTER an Oil Change has been completed on 
the vehicle.

Oil Degradation Counter Reset

This option is necessary on vehicles which have Diesel Particulate Filters (DPF) fitted. 
This is NOT necessary on vehicles with petrol or LPG engines or diesel engines if DPF 
is not fitted. When selected the scan tool will interrogate the vehicle to determine the 
applicability of the function. 

This function allows the resetting of the Oil Degradation Counter and viewing of the Oil 
Degradation parameters (number of resets, Oil Degradation Counter %, km until next 
reset required, odometer at last reset). The counter should only be reset AFTER the 
Oil has been changed. When reset the Counter will be reset to 100%, the number of 
resets will increase by 1.

Summary of Contents for CONTISYS OBD -

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands