manualshive.com logo in svg

VDO CONTISYS OBD -, Instruction Manual

Share
Download
VDO CONTISYS OBD - Instruction Manual Download Page 62

FastCheck

60

Applicable vehicles:

• BMW 1 series (E81/E87)

• BMW 3 series (E90/E91/E92/E93)

• BMW 5 series (E60/E61)

• BMW 6 series (E63/E64)

• BMW 7 series (E65)

• BMW  X5  (E70)

• BMW  X6  (E71)

Note: 

The Multiplexer cable (A2C59512985) or the CAN converter (A2C59512664) 

harness must be used.

Battery change:

After fitting a new battery, the battery change function should be run. The battery 
change function registers the replacement of a battery with the power management 
system. Failure to do so may cause the power management system to operate 
incorrectly.

The battery change application determines the required battery capacity and type 
from the Car Access System (CAS) module. The replacement battery must be same 
capacity and type as displayed. 

Note: 

Certain vehicles require the use of an Absorbent Glass Mat (AGM) battery.

Applicable vehicles:

• BMW 1 series (E81/E87)

• BMW 3 series (E90/E91/E92/E93)

• BMW 5 series (E60/E61)

• BMW 6 series (E63/E64)

• BMW 7 series (E65)

• BMW  X5  (E70)

• BMW  X6  (E71)

Note: 

The Multiplexer cable (A2C59512985) or the CAN converter (A2C59512664) 

harness must be used.

Ford vehicles

Oil Degradation Counter Reset

This option is necessary on vehicles which have Diesel Particulate Filters (DPF) fitted. 
This is not necessary on vehicles with petrol or LPG engines or diesel engines if DPF 
is not fitted. The counter should only be reset AFTER the oil has been changed.

Summary of Contents for CONTISYS OBD -

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands