manualshive.com logo in svg

VDO CONTISYS OBD -, Instruction Manual

Share
Download
VDO CONTISYS OBD - Instruction Manual Download Page 75

FastCheck

73

Follow the on screen instructions which indicate the order the wheels are to be 
programmed in. The spare wheel is included along with the other wheels, but if this 
option is not supported by the vehicle, a message will appear after a few seconds to 
indicate this.

Note

: Remember to reset the correct tyre pressures when finished.

Renault 

General

Note

: For Renault vehicles which use the ‘Renault Card Keyless Ignition System’ and 

the ‘START’ button (Megane II, Scenic II etc.): 

To switch the ignition on WITHOUT starting the engine:

1. Unlock the car with the remote (card).

2. Insert the card into the card reader.

3. Without pressing the brake or clutch pedal push and hold the ‘START’ button for 

at least 5 seconds. The dash should illuminate and the button should be released. 

All diagnostics can now be carried out. 

TPMS is the Tyre Pressure Monitoring System.

Each valve sensor has a unique code and is matched to a particular wheel. This is 
programmed into the UCH control module. This enables a faulty wheel to be identified 
(given that the receiver can identify which wheel is transmitting). The sensor emits an 
RF (Radio Frequency) signal containing the valve code, status and tyre pressure. If 
wheels are to be swapped around then reprogramming will need to be carried out to 
identify the new position of the wheel.

Each valve sensor has a coloured ring attached to the valve nut, each colour 
corresponds to a particular wheel position:

Front Left: Green 

Front Right: Yellow 

Rear Left: Red 

Rear Right: Black

It is recommended that if tyres are moved around that the coloured rings are replaced 
in the correct wheel position.

Each valve sensor will emit a signal every hour if stationary, and every 15 minutes if a 
leak is present. If moving it will emit a signal every minute if no leak is present, and 
every 10 seconds if a leak is present.

Note

: In the live data the tyre pressures will display a default value of 3.5 bar until the 

valves have been forced to transmit.

Summary of Contents for CONTISYS OBD -

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands