VAT 615 DN Series Installation, Operating, & Maintenance Instructions Download Page 1

Page: 1 / 96

Installation, Operating & Maintenance Instructions

Series 615 DN 40 (I.D. 1.5”), RS485

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

289111EB

2013-02-05

1/96

Butterfly control & isolation valve

with extended control range
with RS485 interface

sample picture

This manual is valid for the valve ordering number(s):

61532-KEGJ-0002

configured with firmware

615P.1E.31

The fabrication number is indicated on each product as per the label
below (or similar):

made in Switzerland
Fabrication No.:

615

. .

– . . . . – . . . . / . . . .

– . . . . . .

Fabrication number

Explanation of symbols:

Read declaration carefully before you start any other
action!

Keep body parts and objects away from the valve
opening!

Attention!

Hot surfaces; do not touch!

Loaded springs and/or air cushions are potential
hazards!

Wear gloves!

Disconnect electrical power and compressed air
lines. Do not touch parts under voltage!

Read these

«Installation, Operating & Maintenance Instructions»

and the enclosed

«General

Safety Instructions»

carefully before you start any other action!

Summary of Contents for 615 DN Series

































































































Search results

Summary of Contents for 615 DN Series

Reviews:

VAT 615 DN Series, Installation, Operating, & Maintenance Instructions, Page: 1 / 96

Search results

Summary of Contents for 615 DN Series

Reviews: