manualshive.com logo in svg

Varec 8300 series, Installation And Operation Manual, Page: 63 / 150

Share
Download
Varec 8300 series Installation And Operation Manual Download Page 63

8303

 

Varec, Inc.

53

5.4

Varec Multi-Function Transmitter (Modbus) (MBMFT)

The Varec Multi-Function Transmitter (Modbus) (MFT) Tank Gauge point provides an 

interface to Varec 4200 Multi-Function Transmitters (MFT). The 4200 MFT can 

communicate using a number of different protocols, including Mark/Space and 

Modbus. The MBMFT point interfaces to 4200 MFTs using Modbus. This point 

provides level, temperature, density and volume data. Point and gauge status 

information is also available in this point block. 

5.4.1

Parameters

The database parameters used by the MBMFT point are listed and described below:

Configuration Parame-
ters

Function

Tag

A Tag can contain 15 bytes of data and can include any printable ASCII 

character. Tags can be used to identify the name of the tank being monitored. 

The default tag is set to “MBMFT.00”.

Chan

Physical channel number the MBMFT is connected to. On the 8203 Dual RS-485 

Communications Interface Module, the Chan can be set to 1 or 2. On the 8303 

TGI motherboard, the Chan can be set to 1 or 2.

BaudRate

Baud Rate for communications to the Slave device. Valid values are: 1200, 2400, 

2400, 9600 and 19200. The BaudRate is set prior to scanning the device. The 

default is 9600

ComParams

Defines the number of data bits and the parity used by the com port. Valid 

values include:
8N - 8 data bits, No parity
8O - 8 data bits, Odd parity
8E - 8 data bits, Even parity
7O - 7 data bits, Odd parity
7E - 7 data bits, Even parity
The default is ‘8O’.

ID

Physical Address of the tank gauge transmitter (0-999).

Mode

Operation Mode. Valid values are: 0x80: Swap Mode. Swap the order of integer 

and floating point values.

LevelOffset

Specified the amount of offset to add to the Level. The default is 0.

TempOffset

Specified the amount of offset to add to the Temperature. The default is 0.

LevelDeadband

Specifies the amount of change in the Level that must occur for the level to be 

updated each Change of State period. The default is 0.

TempDeadband

Specifies the amount of change in the Temp that must occur for the 

temperature to be updated each Change of State period. The default is 0.25.

Report

Causes automatic notification to the Host (in response to a Change of State 

Request) when the Value changes State. Parameter value can be High, Low or 

No. Report=No disables notification. Points with Report = High will be sent 

before points with Report = Low. The default is High.

Maxtime

Specifies the maximum time (in secs) between automatic Change of State 

responses being sent to the Host. Report must be set to either Low or High for 

the Value parameter to be sent in response to a Change of State Request. A 

value of 0 disables this option. Non-zero values cause responses to be sent 

even if the value has not changed since the last message. The maximum is 

65535 seconds. The default is 600.

Summary of Contents for 8300 series























































































































































Reviews:

No comments