manualshive.com logo in svg

Varec 8300 series, Installation And Operation Manual, Page: 101 / 150

Share
Download
Varec 8300 series Installation And Operation Manual Download Page 101

8303

 

Varec, Inc.

91

5.14 Varec 4590 Tank Side Monitor (TSM) Interface (TM4590)

The TM4590 point provides an interface to the Varec 4590 Tank Side Monitor. This 

point provides level, temperature, interface and density data. Other information, 

such as point and gauge status, is also available in this Software Block. The 4590 

TSM can communicate using a number of different protocols, including Modbus & 

Whessoe Bus.

5.14.1 Parameters

The database parameters used by the TM4590 point are listed and described below:

Config/Constant 
Parameters

Function

WMSeal

Coded parameter value that enables Weights & Measures password protection.

Tag

A Tag can contain 15 bytes of data and can include any printable ASCII character. 

Tags can be used to identify points indicating the use of the point such as “Tank 

22.” The default tag is set to “TM4590.00”.

Chan

Communications channel to which the gauge is connected. For an 8303 Dual RS-

485 Communications Interface Module or 8311 Current Loop (Whessoe Bus) 

Interface Module Chan is either 1 or 2. 

ID

The Device ID of the 4590 TSM. 

BaudRate

Baud Rate for communications to the Slave device.
8203 Dual RS-485 Communications Interface Module: Valid values are: 2400, 

4800, and 9600. The default is 9600.
8211 Current Loop (Whessoe Bus) Interface Module: Valid values are: 1200, 2400. 

ComParams

Defines the number of data bits and the parity used by the com port. Valid values 

include:
8N - 8 data bits, No parity
8O - 8 data bits, Odd parity
8E - 8 data bits, Even parity
7O - 7 data bits, Odd parity7E - 7 data bits, Even parity
The default is 8N.

Mode

Parameter used to control the operation of the TM4590 point. It has different 

meanings, depending on 8300 TGI is used.
8303 Dual RS-485 Communications Interface Module: 
0x0010: Use old NMS operational status codes
For 8211 Whessoe Bus Communications Interface Module:
0x0: Level, Temp, Pressure, % level, Status, Density, ISH
0x01: Status only
0x02: Level, Temp, % Level, Pressure, ISH only
0x04: Density only
0x08: Level, Temp, %level, pressure only

LevelDeadband

The LevelDeadband sets the deadband for the Change of State mode. The default 

is 0.

TempDeadband

The TempDeadband is used to set the Change of State deadband for the 

temperature. The default is .25 degrees.

FastScanMode

Places the TM4590 point in the Fast Scan mode. Values are Enable or Disable.

Summary of Contents for 8300 series























































































































































Reviews:

No comments