manualshive.com logo in svg

Utax CDC 1725, Instruction Handbook Manual

Share
Download
Utax CDC 1725 Instruction Handbook Manual Download Page 313

Default Setting (System Menu)

8-73

8

Network Setup

The following network settings are available.

• Checking Host Name …8-73
• TCP/IP (IPv4) Setup …8-73
• TCP/IP (IPv6) Setup …8-73
• Protocol Detail …8-75
• NetWare Setup …8-76
• AppleTalk Setup …8-76
• WSD Scan Setup …8-76
• WSD Print Setup …8-77
• Secure Protocol …8-77
• IPSec Setting …8-79
• LAN Interface Setup …8-79

Checking Host Name

Check the host name of the machine. Use the procedure below.

1

Press the 

System Menu

 key.

2

Press [System], [Next] of 

Network

. Check the host name displayed under 

Host Name

.

TCP/IP (IPv4) Setup

Set up TCP/IP to connect to the Windows network.

Refer to 

TCP/IP (IPv4) Setup (by Entering IP Addresses) on page 2-13

 about the procedures.

TCP/IP (IPv6) Setup

Set up TCP/IP (IPv6) to connect to the network. The default settings are "TCP/IP Protocol: 

On

, TCP/IP (IPv6): 

Off

. Use the procedure below.

1

Press the 

System Menu

 key.

2

Press [System], [Next] of 

Network

 and then [Next] of 

TCP/IP Setting

.

3

Press [Change] of 

TCP/IP

.

4

Press [On] and then press [OK].

5

Press [Next] of 

IPv6

.

6

Press [Change] of 

IPv6

.

7

Press [On]. 

IP Address (Link Local)

 appears.

8

Press [OK].

9

After changing the setting, restart the system or turn the machine OFF and then ON again. 

For detailed information on restarting the system, refer to 

Restarting the System on page 8-72

.

Summary of Contents for CDC 1725





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands