UNMAK UKY/DUOPEL 100 User Manual Download Page 13

P a g e

 | 12

 

 

 

ÜKY/Duopel Boilers User Manual

 

BOILER FEAUTURES 

 

 

 

1. Control panel 

5. Return line 

9. Water jackets 

2. Gearmotor  

6. Safety flow 

10. Grid for log wood burning 

3. Fan 

7. Safety return 

11. Wood pellet burner 

4. Hot water flow 

8. Hopper 

 

 
 

1. Control panel: It is the electronic box that blows the boiler. It controls when the gearbox, motor, fan, pump 
stop and when to run. The temperature values read while controlling are effective. 
2. Geared motor: It is used to increase the power by decreasing the speed of the motor. The movement of the 
auger  gives  the  gearmotor.  The  safety  device  in  the  pellet  feed  line  also  gets  its  movement  from  this 
gearmotor. 
3. Fan: It is the fan that provides the combustion air. It can be adjusted to operate at the desired speed from 
the control panel. 
4. Hot water flow line: It is the flow pipe to the radiators or heating system. The water heated in the boiler is 
sent to the radiators or heating installation from this pipe. 
5. Return line: It is the pipe through which the water returned from the radiators or heating installation returns 
to the boiler. It can also be called return pipe or return line. 
6.  Safety  flow  line:  It  can  also  be  called  expansion  line.  It  is  the  line  where  the  expanded  water  is  sent  as  a 
safety due to heating in the boiler. 
7. Safety return line: It is the line where the water sent from the boiler to the expansion tank is taken back. 
8. Hopper: It is the place where the fuel is stored. The power it can take depends on the fuel size. 
9. Water jackets: These are specially designed water chambers to circulate the water and circulate the smoke. 
As the smoke passes between them, it releases its energy and heats the water inside. 
10.  Grid:  These  are  the  pipes  used  for  burning  wood.  Water  passes  through  the  pipes.  In  this  way,  both  the 
water inside is warmed and the life of the grid is extended. 
11. Pellet burner: It consists of two nested chambers. Pellet fuel is driven from the inside by the helix and the 
air coming from the outside is blown by the fan. Fan air and fuel meet at the front of the burner. 

Summary of Contents for UKY/DUOPEL 100



























Reviews: