background image

•  IMPORTANT: Read this entire manual before installing 

and operating this product. Failure to do so may result 

in property damage, bodily injury, or even death. 

Proper installation of this stove is crucial for safe and 

efficient operation.

• 

Install  vent  at  clearances  specified  by  the  vent 

manufacturer.

• 

If a chimney or creosote fire occurs, press the “OFF” 

button immediately. Do not unplug the unit.

•  Do not connect the pellet vent to a vent serving any 

other appliance or stove.

• 

Do  not  install  a  flue  damper  in  the  exhaust  venting 

system of this unit.

•  Use of outside air is not required for this unit.

• 

Contact  your  local  building  officials  to  obtain  a 

permit and information on any additional installation 

restrictions or inspection requirements in your area.

•  Do not throw this manual away. This manual has 

important operating and maintenance instructions 

that you will need at a later time. Always follow the 

instructions in this manual.

•  This appliance is designed for the use of pelletized fuel 

that meet or exceed the standard set by the Pellet Fuel 

Institute(PFI), The use of other fuels will void warranty.

•  Never use gasoline, gasoline-type lantern fuel, 

kerosene, charcoal lighter fluid, or similar liquids to start 

or ’freshen up’ a fire in this stove. Keep all such liquids 

well away from the stove while it is in use.

•  A working smoke detector must be installed in the 

same room as this product.

• 

It must be installed at least 15 feet (4,57 m) from the 

appliance in order to prevent undue triggering of the 

detector when reloading.

•  Do not unplug the stove if you suspect a malfunction. 

Turn  the  ON/OFF  SWITCH  to  ”OFF’  and  contact  your 

dealer.

•  Your stove requires periodic maintenance and 

cleaning  (see  ”MAINTENANCE  ”).  Failure  to  maintain 

your stove may lead to improper and/or unsafe 

operation.

•  Disconnect the power cord before performing any 

maintenance! NOTE: Turning the ON/OFF Switch to 

”OFF” does not disconnect all power to the electrical 

components of the stove.

•  Never try to repair or replace any part of the stove 

unless instructions for doing so are given in this manual. 

All other work should be done by a trained technician.

•  Do not operate your stove with the viewing door 

open. The auger will not feed pellets under these 

circumstances and a safety concern may arise from 

sparks or fumes entering the room.

•  The feed door must be closed and sealed during 

operation.

• 

Never block free airflow through the open vents of the 

unit.

•  DO NOT CONNECT TO OR USE IN CONJUNCTION WITH 

ANY AIR DISTRIBUTION DUCTWORK UNLESS SPECIFICALLY 

APPROVED FOR SUCH INSTALLATION.

•  Allow the stove to cool before performing any 

maintenance or cleaning. Ashes must be disposed 

in a metal container with a tight fitting lid. The closed 

container of ashes should be placed on a non-

combustible surface or on the ground, well away from 

all combustible materials, pending final disposal.

• 

The exhaust system should be checked monthly during 

the burning season for any build-up of soot or creosote.

•  Do not touch the hot surfaces of the stove. Educate all 

children on the dangers of a high-temperature stove. 

Young children should be supervised when they are in 

the same room as the stove.

•  The hopper and stove top will be hot during operation; 

therefore, you should always use some type of hand 

protection when refueling your stove.

•  A power surge protector is required. This unit must be 

plugged into a 110 - 120V, 60 Hz grounded electrical 

outlet. Do not use an adapter plug or sever the 

grounding plug. Do not route the electrical cord 

underneath, in front of, or over the heater. Do not 

route the cord in foot traffic areas or pinch the cord 

under furniture.

•  The heater will not operate during a power outage. 

If a power outage does occur, check the heater for 

smoke spillage and open a window if any smoke spills 

into the room.

•  Keep foreign objects out of the hopper.

•  The moving parts of this stove are propelled by high 

torque electric motors. Keep all body parts away from 

the auger while the stove is plugged into an electrical 

outlet. These moving parts may begin to move at any 

time while the stove is plugged in.

• 

Do not place clothing or other flammable items on or 

near this stove.

•  When installed in a mobile home, the stove must be 

grounded directly to the steel chassis and bolted to 

the floor. WARNING—THIS UNIT MUST NOT BE INSTALLED 

IN THE BEDROOM (per HUD requirements). CAUTION—

The structural integrity of the mobile home floor, wall, 

and ceiling/roof must be maintained.

•  This appliance is not intended for commercial use.

• 

Establish a routine for the fuel, wood burner and firing 

technique. Check daily for creosote build-up until 

experience shows how often you need to clean to be 

safe. Be aware that the hotter the fire the less creosote 

is deposited, and weekly cleaning may be necessary 

in mild weather even though monthly cleaning may 

be enough in the coldest months. Contact your local 

municipal  or  provincial  fire  authority  for  information 

on  how  to  handle  a  chimney  fire.  Have  a  clearly 

understood plan to handle a chimney fire.

* This appliance is a freestanding heater. It is not intended to be attached to any type of ducting. It is not a furnace.

Safety Precautions

Summary of Contents for King

















































Reviews: