background image

INSTALLER:  Leave this manual with the appliance.

CONSUMER:  Retain this manual for future reference.

INSTALLATEUR:  Laissez cette notice avec l'appareil.

CONSOMMATEUR:  Conservez cette notice pour consulta-

tion ultérieure.

- Do not store or use gasoline or other flammable vapors and 

liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance. 

•  Do  not  touch  any  electrical  switch;  do  not  use  any 

phone in your building. 

• Immediately call your gas supplier from a neighbor’s 

phone.  Follow the gas supplier’s instructions. 

•  If  you  cannot  reach  your  gas  supplier,  call  the  fire 

department.

-   Installation and service must be performed by a quali-

fied installer, service agency or the gas supplier.

WARNING:  If the information in these instructions is 

not followed exactly, a fire or explosion may result 

causing property damage, personal injury or death.

- Ne  pas  entreposer  ni  utilizer  d’essence  ni  d’autres 

vapeurs ou liquides inflammables dans le voisinage 

de cet appareil ou de tout autre appareil.

- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir 

des téléphones se trouvant dans le bâtiment où vous 

trouvez. 

•  Appelez  immédiatement  votre  fournisseur  de  gaz 

depuis un voisin. Suivez les instructions du fournis-

seur. 

• Si vous ne pouvez rejoindre le fournisseur de gaz, 

appelez le service des incindies.

- L’installation et l’entretien doivent être assurés par un 

installateur ou un service d’entretien qualifié ou par 

le fournisseur de gaz.

AVERTISSEMENT:  Assurez-vous de bien suivre les 

instructions données dans cette notice pour réduire 

au minimum le risque d’incindie ou d’explosion ou 

pour éviter tout dommage matériel, toute blessure 

ou la mort.

INSTALLATION AND OPERATION

Ce manuel d’installation est disponible en francais, s  implement en faire 
la demande. Numéro de la pièce 775227CF.

MODELS

US

Portland

P/N 775227M  REV. F  09/2011

Direct-Vent
VINTAGE™

This appliance may be installed in an aftermarket permanently located, manufactured  home (USA only) or mobile 

home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating 

plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

WARNING AVERTISSEMENT

UNE SURFACE VITRÉE CHAUDE PEUT 

CAUSER DES BRÛLURES.

LAISSER REFROIDIR LA SURFACE 

VITRÉE AVANT D'Y TOUCHER.

NE PERMETTEZ JAMAIS À UN ENFANT 

DE TOUCHER LA SURFACE VITRÉE.

HOT GLASS WILL

 CAUSE BURNS.

DO NOT TOUCH GLASS

 UNTIL COOLED.

NEVER ALLOW CHILDREN TO 

TOUCH GLASS.

OTL Report No. 50-S-11b-5

VINT-DVS-U   

SDVCS

DR

AF

T

8/3

1/2

01

1

Summary of Contents for VINTAGE SDVCS

































Reviews: