LOAD HANDLING
LOAD HANDLING
3-9
3-9
UNSTACKING
UNSTACKING
1)
1)
When approaching the area where the load is to
When approaching the area where the load is to
be retrieved, slow down the truck.
be retrieved, slow down the truck.
2)
2)
Stop the truck right in front of the l
Stop the truck right in front of the l
oad where the
oad where the
distance between the fork tips and the load is
distance between the fork tips and the load is
about 30 cm.
about 30 cm.
3)
3)
Check the condition of
Check the condition of
the stack.
the stack.
4) Tilt the forks forward until they are horizontal.
4) Tilt the forks forward until they are horizontal.
If the forks are not in the correct position for
If the forks are not in the correct position for
stacking, operate the side-shift lever carefully to
stacking, operate the side-shift lever carefully to
put them where they should be. Raise the forks
put them where they should be. Raise the forks
until the pallet is in the right position.
until the pallet is in the right position.
WARNING
WARNING
When handling loads with the side-shifter,
When handling loads with the side-shifter,
observe the following conditions; otherwise
observe the following conditions; otherwise
there is a danger that the truck will tip over
there is a danger that the truck will tip over
on its side because lateral balance was lost.
on its side because lateral balance was lost.
•
•
Do not t
Do not t
ravel with an off-
ravel with an off-
center load on t
center load on t
he
he
forks. Never lift an uneven load.
forks. Never lift an uneven load.
•
•
Do not o
Do not o
perate the side-shifter
perate the side-shifter
while lifting
while lifting
a load.
a load.
•
•
Do not
Do not
operate the side-shifte
operate the side-shifte
r with
r with
the
the
forks raised high (150 cm or higher), except
forks raised high (150 cm or higher), except
when the load can be stabilized, as it is
when the load can be stabilized, as it is
over a shelf.
over a shelf.
•
•
Do not operate the side-shifter while
Do not operate the side-shifter while
traveling. Do not jerk
traveling. Do not jerk
the side-shifter.
the side-shifter.
CAUTION
CAUTION
Side-shifting operations should be performed
Side-shifting operations should be performed
with the forks raised 5 to 10 cm above the top
with the forks raised 5 to 10 cm above the top
surface of the outriggers.
surface of the outriggers.
Do not try to side-shift the load with the bottom
Do not try to side-shift the load with the bottom
of the forks in contact with the ground or floor
of the forks in contact with the ground or floor
surface; otherwise the side-shifter might be
surface; otherwise the side-shifter might be
damaged.
damaged.
5) Make sure the forks are positioned properly for
5) Make sure the forks are positioned properly for
the pallet. Move back slowly and stop the truck.
the pallet. Move back slowly and stop the truck.
6) Insert the forks into the pallet as far as possible
6) Insert the forks into the pallet as far as possible
by advancing the mast.
by advancing the mast.
*
*
If the forks
If the forks
are hard to
are hard to
be fully inserted,
be fully inserted,
use
use
the following procedure:
the following procedure:
Insert 3/4
Insert 3/4
of
of
the forks
the forks
and raise
and raise
them 5
them 5
to
to
10 cm. Pull back the pallet or skid about 10
10 cm. Pull back the pallet or skid about 10
to 20 cm and lower the pallet or skid on the
to 20 cm and lower the pallet or skid on the
stack. Insert the forks into the pallet fully.
stack. Insert the forks into the pallet fully.
7) Raise the forks 5 to 10 cm off the stack and
7) Raise the forks 5 to 10 cm off the stack and
fully retract the mast by operating the reach
fully retract the mast by operating the reach
mechanism.
mechanism.
8)
8)
Make sure there is no one or obstacle in fr
Make sure there is no one or obstacle in fr
ont of
ont of
the truck and move forward slowly to the
the truck and move forward slowly to the
position
position
where the load can be lowered to a safe height.
where the load can be lowered to a safe height.
9) Slowly lower the load to a height of 5 to 10 cm
9) Slowly lower the load to a height of 5 to 10 cm
above the upper surface of the outriggers. Tilt
above the upper surface of the outriggers. Tilt
back the forks fully and move to the desired
back the forks fully and move to the desired
area.
area.
https://www.forkliftpdfmanuals.com/
Summary of Contents for FRSB14-8
