UNI-T UTD2025C Operating Manual Download Page 17

Page: 17 / 120

Operating Manual for UTD2000/3000

General inspection

Function inspection

It is suggested to inspect the instrument by

following steps when getting a new UTD2000/3000

series digital storage oscillograph.

1. To check if there is damage due to transportation

or not.

Please replace carton or foaming plastic protection

cushion with severe damage instantly.

2. Please inspect fitting details and shown it in

“Fittings of UTD2000/3000 series digital Storage

Oscillograph” shown in the manual. You can check

if there are deficient fittings or not by referring to it.

Please contact UNI-T distributor or local agent if

there are deficient or damaged fittings.

3. Please inspect the entire machine and contact UNI-T

distributor or local agent for damaged appearance,

abnormal operation or failing to pass performance test.

Please pay attention to packages and report to

transportation department and UNI-T distributor if

machine damage is caused by transportation.

1. Connect the power supply

You can supply power to the machine and voltage is AC

100V to AC 240V. Frequency is 45Hz to 440Hz. It has

to press [UTILITY] menu and [F1] for self-correction

after power supply 30 minutes after operation of hot

machine so that digital storage oscillograph operates

under the best status. As shown in Figure 1

4, please

enter into next page and press [F1] to call out ex-factory

setup.

㧙

UNI-T will arrange maintenance or replacement.

Please carry out once fast function inspection to

check if the machine operates normally or not.

Please operate according to following steps:

Summary of Contents for UTD2025C

























































































































Search results

Summary of Contents for UTD2025C

Reviews:

Related manuals for UTD2025C

Brands by name

Popular brands

UNI-T UTD2025C, Operating Manual

Search results

Summary of Contents for UTD2025C

Reviews:

Related manuals for UTD2025C

Brands by name

Popular brands