UNI-T UTD2025C Operating Manual Download Page 117

Page: 117 / 120

Appendix C: Maintenance and cleaning

General maintenance

Cleaning:

It is not allowed to store or place instruments in

locations with direct sunshine for LCD for a long

time. Note: It is not allowed to touch instrument or

probe by pressurized spray, liquid or solvent to

avoid damage.

Instrument and probe can be inspected constantly

according to operation.

Please clean outer surface of instruments

according to following steps:

1. Please remove floating dust out of instrument

and probe by soft cloth. Please do not scratch

transparent LCD protection screen during cleaning.

2. Please power off when cleaning the instrument

by wet soft cloth without dripping. It can be cleaned

by soft detergent or clean water. It is not allowed to

use any corrosive chemical detergent to avoid

damage to instrument or probe.

Warning: Please confirm that instrument has been

dried thoroughly before power re-supply to avoid

electric short-circuit even personal injury due to

moisture.

105

Operating Manual for UTD2000/3000

Summary of Contents for UTD2025C

























































































































Search results

Summary of Contents for UTD2025C

Reviews:

Related manuals for UTD2025C

Brands by name

Popular brands

UNI-T UTD2025C, Operating Manual

Search results

Summary of Contents for UTD2025C

Reviews:

Related manuals for UTD2025C

Brands by name

Popular brands