UNI-T UTD2025C Operating Manual Download Page 102

Page: 102 / 120

mode shall be used for video signals. Waveform can

not be displayed stably until setting correct trigger

mode.

Please strive to set coupling to high-frequency

inhibition and low-frequency inhibition display to

filter high low frequency noise triggered by

interference

5. To press RUN/STOP key without any display:

To check if trigger mode of trigger menu is in

normal or single gear or not. It has to check if trigger

level is out of waveform scope or not.

Trigger level shall be in the middle or trigger mode

shall be set to AUTO gear if yes.

To press AUTO key for automatic setup as

above.

6. Display speed will reduce after opening average

time sampling mode.

In general

speed will reduce normally if

average times exceed

To reduce average times.

7. Staircase waveform display

As normal phenomenon, horizontal time base

can increase under super-low horizontal time base

gear so as to increase horizontal resolution and

improve display.

Possible display type is vector and sampling

points can be connected for staircase waveform

display. Display type can be set to point display

Operating Manual for UTD2000/3000

Summary of Contents for UTD2025C

























































































































Search results

Summary of Contents for UTD2025C

Reviews:

Related manuals for UTD2025C

Brands by name

Popular brands

UNI-T UTD2025C, Operating Manual

Search results

Summary of Contents for UTD2025C

Reviews:

Related manuals for UTD2025C

Brands by name

Popular brands