background image

Page 24 

Maintenance 

 

printed: 06/2020  Subject to change! 

:FFUserManual.docx 

   

  Remove the burner nozzle assembly from the injector case (cast iron part) after unscrewing the 

fixing screw at the injector case and the union of the gas supply from the all gas valve. 

  Remove the injector and the tube angle from the burner socket. 

  Loosening of the 3 unions between burner and the support profile below the burner. 

  Remove the burner. 

The re-assembling is to be made in reversed sequence. 

6.5.6  All gas valves 

  Remove the lower fat drawer and the bottom plate. 

  Remove the thermo element from the main gas supply and from the gas lead to the burner by 

loosening the unions. 

  Remove the thermo element from the all gas valve. (The connection of the thermo element is 

behind the all gas valve.) 

  Remove the all gas valve from the main gas supply and from the gas lead to the burner after 

loosening of the unions. 

  Remove the all gas valve. 

The re-assembling has to be made in reversed sequence. 

6.5.7  Motor 

  Remove the lower fat drawer and the bottom plate. 

  Loosen the 2 screws from the protection plate above the motor and remove it. 

  Unplug the motor. 

  Loosen the chain tension union from the support of the motor (is to be find in front of the motor). 

  Remove the support with motor after you have removed the hinge pin and the gear wheel of the 

gear shaft from the chain. 

  Loosen 4 X screws between the motor and the support and remove the motor. 

The re-assembling is to be made in reversed sequence. 

6.6  Trouble shooting 

If your Rotisserie Wall of Flame does not work satisfactorily, we would like to give a first help with 

the following checklist. Only after checking these points you should contact: 
a) your responsible service partners 
or 
b)  directly the company:  UBERT GASTROTECHNIK GmbH 

Werk II Gewerbegebiet Nord 

Vennekenweg 17 

46348 Raesfeld 

Tel.:(49) 02865 / 602-226 

Service-Tel.:0172 / 2 82 86 31 

Fax:(49) 02865 / 602-102 (or -103) 

 

Only these two companies are allowed to carry out service work and replacement of 

defect parts. If you do not observe this note or in case of manipulation of a third party 

any claims for guarantee will become invalid! 

 

Summary of Contents for FF Series
































Reviews: