background image

Page 6 

Important References 

 

printed: 06/2020  Subject to change! 

:FFUserManual.docx 

2.5  Special safety notes for the user 

 

2.5.1  Safety devices (Protection units) 

  Before setting the appliance into operation all safety devices and all removable parts 

have to be fitted and must operate in working order. 

  Safety devices may only be removed after switching off the appliance completely. You 

must make sure, that the appliance cannot be switched on again during maintenance 

processes. 

  All parts and components have to be fitted according to the regulations. 

2.5.2  For your information (Informing safety steps) 

  These operating instructions should be kept always together with the appliance. 

  Supplementing to the operation instructions within this manual all local regulations for 

accident prevention and for the protection of the environment are to be considered.  

  All stickers for safety and possible hazards on the appliance have to be in a good 

readable condition and in a visible position. 

2.5.3  Personnel training 

  Only trained and instructed personnel is allowed to operate the appliance. 

  The responsibilities of the personnel are to be determined clearly for installing, start-

up, operation, assembling, and servicing of the unit. 

  Personnel not being trained yet are only allowed to operate the unit under supervision 

of a trained and experienced person. 

2.5.4  Operating the controls 

  Only trained personnel is allowed to operate the controls. 

2.5.5  Safety check during operation 

  Only operate the appliance if all safety devices are working properly. 

  Before switching on, make sure that there is no danger for any person while the ap-

pliance is starting to operate. 

  Check appliance at  least once per day with regard to visible damages and to the 

function of all safety devices. 

2.5.6  Possible hazards caused by electric energy 

  Repair works on electrical leads and devices must be carried out by qualified electri-

cians only. 

  The connection must follow the rules of the local determinations. 

  Check the electrical components of the appliance on a regular basis. Wiring being 

connected improper or melted cables have to be repaired immediately. 

  If there is a need of repair works on life electrical components, always a second per-

son is required to attend and to switch off the main switch in case of emergency. 

2.5.7  Special areas of danger 

  All removable parts are only to be removed if the Wall of Flame Rotisserie is switched 

off and all surfaces and parts are not hot anymore! 

  Caution while removing grilled food! All parts may be hot and may cause severe burn-

ings to your skin. Do not reach into the rotisserie while the appliance is hot and oper-

ating. Before removing the waste fat pan take out the waste liquids. 

Summary of Contents for FF Series
































Reviews: