UAZ PATRIOT Operation Manual Download Page 16

Page: 16 / 184

Minimum turning circle along

the axle, external (relative to

the turning center) wheel, m,

max.

6.55

7.08

Minimum turning circle,

external, by the front bumper

point, the most distant from

the turning center, m. max.

6.8

7.35

Maximum climb covered by a

motor vehicle of gross weight,

degree ( %)

31 (60)

Inmost wading depth, m

0.5

engine

Model

ZMZ-40906

ZMZ-51432

Designation

UAZ-3163, UAZ-23632, UAZ-23602

UAZ-31638, UAZ-23638,UAZ-23608

Type

four-stroke, with spark-plug ignition

diesel turbo-charged

Cylinder number

Four

Cylinder arrangement

In-line, vertical

Firing order

1-3-4-2

Cylinder diameter, mm

95.5

Piston stroke, mm

Summary of Contents for PATRIOT

























































































































































































Search results

Summary of Contents for PATRIOT

Reviews:

Related manuals for PATRIOT

Brands by name

Popular brands

UAZ PATRIOT, Operation Manual

Search results

Summary of Contents for PATRIOT

Reviews:

Related manuals for PATRIOT

Brands by name

Popular brands