manualshive.com logo in svg

Twilight MC-SUP2000H, Manual

Share
Download
Twilight MC-SUP2000H Manual Download Page 3

IV

4.4.1. Signal strength and quality

..............................................................

- 42 -

4.4.2. Transfer time ratio

.............................................................................

- 43 -

4.5. Measurement data view

..............................................................................

- 43 -

4.6. Measurement data processing

...................................................................

- 43 -

Chapter 5 Data processing

.........................................................................................

- 44 -

5.1. Processing of the measured data

..............................................................

- 44 -

5.2. Printing of measurement data

....................................................................

- 44 -

5.3. Storage of measurement data

....................................................................

- 45 -

5.4. Analysis and statistics of measurement data

...........................................

- 45 -

Chapter 6 How To

........................................................................................................

- 46 -

6.1. How to judge if the instrument works properly

.........................................

- 46 -

6.2. How to judge the liquid flowing direction

..................................................

- 46 -

6.3. How to change between units systems

....................................................

- 47 -

6.4. How to select a required flow rate unit

......................................................

- 47 -

6.5. How to use the totalizer multiplier

..............................................................

- 47 -

6.6. How to open or shut the totalizers

.............................................................

- 47 -

6.7. How to reset the totalizers

..........................................................................

- 47 -

6.8. How to restore the flow meter with default setups

..................................

- 47 -

6.9. How to use the damper

...............................................................................

- 47 -

6.10. How to use the zero-cutoff function

.........................................................

- 47 -

6.11. How to setup a zero point

.........................................................................

- 48 -

6.12. How to get a scale factor for calibration

.................................................

- 48 -

6.13. How to use the operation locker

..............................................................

- 48 -

6.14. How to use the built-in data logger

..........................................................

- 48 -

6.15. How to use the Frequency Output

...........................................................

- 49 -

6.16. How to use the Totalizer Pulse Output

...................................................

- 49 -

6.17. How to produce an alarm signal

..............................................................

- 50 -

6.18. How to use the built-in Buzzer

.................................................................

- 50 -

6.19. How to use the OCT output

......................................................................

- 50 -

6.20. How to modify the built-in calendar

.........................................................

- 51 -

6.21. How to adjust the LCD contrast

...............................................................

- 51 -

6.22. How to use the RS232 serial interface

...................................................

- 51 -

Summary of Contents for MC-SUP2000H






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands