Tryton TFV18B2, Operating Instruction

Page: 5 / 52

5
Using the charger:
a) Use only dedicated power adapters to charge the battery.
Application of a power adapter dedicated to charge another type of the
Fig.F
battery unit poses a risk of fires.
b) The supplied charger should only be used for charging batteries
Fig.G
that are supplied together with it. Charging other batteries may
cause breaking and disintegration of the battery, bodily harm, or fire.
c) Do not disassemble the charger.
d) The charger is designed exclusively for indoor use. It must not be
exposed to water or moisture.
e) Charge only in an ambient temperature between 15-25
degrees.
f) Do not insert metal objects of any kind into the charger.
device
The vibration level value given refers to basic application of the tool. If the
tool is used for other applications or with other tools, or if it is not
n
maintained properly, the vibration level may differ from the values given.
The above-mentioned causes may lead to higher exposure to vibrations
ź
during the whole work time.
ź
One must implement additional safety measures to protect the operators
ź
from exposure to vibrations, such as maintenance of the electric tool and
ź
work tools, assurance of proper hand temperature, or determination of the
sequence of work operations.
The declared total vibrations and declared noise emissions were measured
in accordance with a standard test method and may be used for tool
ź
comparison.
ź
The declared total vibrations and noise emissions can be used in preliminary
ź exposure assessment.
Warnings:
n
The vibrations and noise emissions during the actual use of the power tool
may differ from the declared values depending on how the tool is used and
on the type of the workpiece in particular.
Determine safeguards to protect the operator. They should be based on the
estimated exposure under actual operational conditions (taking into
account all parts of the operating cycle such as when the tool is switched off
4 . Gear shifter
or idle except the start time).
n
Battery
Battery lock clip
On/off switch
APPLICATIONS AND CONSTRUCTION:
Despite using the tool according to its intended application it is impossible
to eliminate certain residual risk factors. Considering the tool construction
the following risks may occur when operating the tool:
- Touching the rotating drill bit with the hand
operator's clothes .
- Burns when changing drill bits (Drill bits heat up intensely during
operation; use protective gloves when changing the drill bit).
- Throwing back machined object or its fragment.
- Bending/breaking the drill.
Device components
Fig.C 12.
The device is dedicated to drive in and out screws, drilling boreholes in such
materials as steel, wood, plastics, etc. The combo drill and screwdriver is
designed exclusively for DIY applications
.
The set contains:
Cordless drill/s crewdriver -1
Battery - 2 s
-1
:
- -1
- - 6 s (P H 1, P H 2, PZ1, PZ2, SL 5 , SL 6 )
- - 6 s ( 1,5; 2,5; 3; 4; 5 ; 6 mm)
Carrying case -1
-1
O perating instruction -1
The numbering of device components refers to graphics presented on page 2 of
the user's manual:
Fig.A 1. Keyless chuck
2. Clutch control knob
3.
5. Rotation direction switch
6. H andle
7.
Charging the battery
The driver is supplied with a partially charged battery. Charge the battery
fully before use. It is recommended that the first charging session lasts at
least
5 hour s .
The tool must not be used for work requiring a professional tool.
Any use of the that is not in observance with the above-mentioned
purpose is forbidden, leads to the loss of warranty, and relieves the
manufacturer from responsibility for the resulting damage.
Any modifications of the tool by the user relieve the manufacturer from
responsibility for any damage and injuries to the user and the surroundings.
TECHNICAL PARAMETERS
or
pc .
pc .
pc .
Working bits set
magnetic tip for bits with a 1/4" holder pc .
bits pc .
drills pc .
pc .
Warranty card pc .
pc .
Battery capacity indicator
PREPARATION FOR WORK:
Fastener to hang on the belt
11. Auxiliary lighting
Charger
13. Clutch setting indicator
14. Drilling setting pictogram
15. Left-threaded fixing screw
:
Charger
8.
9.
10.
MODEL TFV18B2
Rotation speed under no-load conditions , I/II Gear
Supply voltage
Chuck clamping range
Sound pressure level (LpA)
Sound power level (LwA)
Vibration level according to:
t olerance of measurements K=1,5 m/s²) (
EN 62841-1-2
Weight (with battery)
B attery type Li-ion
Rated voltage
Charging time
Mains voltage
0-400/ rpm 0-1500
100- 2 4 0 V
3 -5 h
2
a = 2,29 m/s
h,D
92 dB(A)
81 dB(A)
ø 0,8-10 mm
Electric capacity 150 0mAh
DC 18 V
1,135 kg
T olerance of measurements pA, KwA 5 dB(A) K
1 8V
B attery charger
Frequency 50/ 60 Hz
Output current (DC) 21,5V/ 0,37A
Power consumption 8W