Tryton TFV18B2, Operating Instruction

Page: 6 / 52

1.
n
see
3. Connect charger to an electrical socket 100-240 V, 50/60Hz.
n
Battery charging indicator
After charging, disconnect the charger and remove the battery.
The lithium-ion battery can be charged at any moment, without
detriment to its life. Interrupting the charging process does not entail a
n
n
n
To drill deep boreholes carry out your job gradually, drill to lower
depths and remove the drill from the borehole from time to time to
remove borings from the borehole.
To drill large diameter boreholes it is recommended to start with
drilling a low-diameter borehole and then expand it to the desired
diameter. It prevents the tool from overloads.
When the drilling bit is seized during working switch immediately the
tool off to prevent it from being damaged. Switch the rotations
Press the battery lock button ( 9 ) and remove the battery ( 8 ) from the Shifting gear ( Fig. A )
drill-driver ( see fig. B ).
The gear shifter ( 4 ) makes it possible to choose 2 rotation speed ranges.
2. Connect the battery ( 8 ) to the charger ( 1 2 ) (see fig. C ).
Gear I: Used for driving and unscrewing screws.
Gear II: Used for drilling.
CAUTION: Do not change the position of the gear shifter ( 4 ) during tool
operation as this may damage the gear box. Always allow the tool to come
The red battery lamp is lit during the charging process. When the battery
to a full stop before changing the setting of the gear shifter.
is fully charged, the red lamp goes out and the green one is lit.
If the gear shifter does not move all the way, move the drive spindle
The charging current reduces with the charging progress. After about 3
slightly.
hours the charging current reaches the stable, minimum value (trickle
charging) to prevent battery overcharging and damage.
n
Changing the chuck ( Fig. G )
To free a seized bolt
hit is gently on its head.
n
Battery capacity indicator
The battery capacity indicator ( 3 ) indicates the battery is empty with two
LEDs.
Green LED is lit:
The battery is fully charged.
Green and red LEDs are lit:
The battery is sufficiently charged.
n
ź
The practical fastener ( 7 ) can be used for attaching the drill-driver on Only red LED is lit:
the user's belt, both for right-hand and left-hand dominant users.
The battery is empty, it needs charging.
ź
n
Work tool replacement
n
2.
3.
see
risk of damaging the battery cells.
IN USE:
Turning on/off
The switch ( 10 ) has fluid rotation speed adjustment built-in.
Press the switch to activate the power tool. The rotation speed will
increase the further the switch is pushed. To stop the power tool, release
the switch.
Auxiliary components
Choosing rotation direction ( see Fig. E )
The driver can work with clockwise (right) or counter-clockwise (left)
rotation.
- to select clockwise rotation, move the clockwise/counter-clockwise
slider (
5 ) to the left (looking from the back of the driver),
- to select counter-clockwise rotation, move the clockwise/counter-
clockwise slider (
5 ) to the right (looking from the back of the driver),
When the tool switch ( 10 ) is released the drill chuck is locked. It enables
When the rotation direction switch is in the middle position, it is locked.
quick, easy and convenient replacement of a working tool installed in the
For drilling and driving screws in, clockwise operation should be
drill chuck. To remove a drill (or a working bit) from the drill chuck, rotate
selected. For taking out the drill bit, removing a stuck drill bit, or
the chuck ring anticlockwise to expand the opening of the chuck. Insert a
unscrewing screws, counter-clockwise operation should be selected.
new drill (or a working bit) into the chuck and rotate the chuck ring
Choosing torque ( see Fig. F )
clockwise to secure the drill in the drill chuck.
The driver is equipped with a ring ( 2 ), which can be used for setting the
Drills (or other working bits) must be moved to the full depth of the chuck
toque when driving screws. The ring has 22 settings, from 1 to 21 , and a
opening.
drilling setting.
Drilling boreholes
Using a given setting (from 1 - 21 ) means that the clutch is set to an
assigned toque. This makes it possible to prevent a screw from being
driven too far or being damaged. Different torques should be used for
different screws and materials.
Always start with a low torque and increase gradually until the desired
result is achieved.
For drilling in metal, wood or plastic, set the ring (
2 ), so that the indicator
( 1 3 ) points to symbol ( 1 4 ) .
1. Disconnect the battery ( 8 ) from the driver.
2. Open the chuck as much as possible ( 1 )
3. Using a PH 2 (Philips No.2) screwdriver, rotate the fixing screw ( 15 ) of
the chuck clockwise ( CAUTION! L eft-thread ).
4. Hold the lower chuck ring (the one closer to the driver body) and
rotate the drill/driver chuck counter-clockwise (looking from the
point of view of the chuck).
CAUTION: A jammed keyless chuck ( 1 ) can be released by inserting the
short end of a hex key in the chuck and lightly tapping the longer arm of
the key (see Fig.
D ).
5. To attach the chuck, screw it onto the drive spindle counter-clockwise
(looking from the chuck side) and secure by screwing in the fixing
screw counter-clockwise using a PH 2 screwdriver (No.2 Philips). For
the chuck not to rotate during screwing in the fixing screw, the chuck
should be held by the lower ring (the one closer to the drill/driver
body).
The drill/driver is equipped with an auxiliary light ( 1 1 ) for the area of
drilling/driving, which turns on after the appropriate switch ( 10 ) is
pushed.
CAUTION: Disconnect the battery from the driver or put the rotation
direction switch ( 5 ) in the middle position to secure the machine from being
started by mistake, which could in turn cause harm to the user.
1.
6