Tripp Lite NGI-M08C4-L2 Owner'S Manual Download Page 50

Page: 50 / 313

5.2.3.

Age Time Settings

5.2.3.1.

CLI Configuration

Node

Command

Description

enable

show mac-address-table

aging-time

This command displays the current MAC address

table age time.

enable

configure terminal

This command changes the node to configure node.

configure mac-address-table aging-

time VALUE

This command configures the mac table aging time.

The range is 20 to 500 or 0: disable.

Example:

L2SWITCH(config)#mac-address-table aging-time 200

Success!

L2SWITCH#show mac-address-table aging-time

The mac-address-table aging-time is 200 sec.

5.2.3.2.

Web Configuration

Parameter

Description

Age Time Setting

Age Time

Configure the age time; the valid range is from 20 to 500 seconds. The

default value is 300 seconds. 0 means that the system will not age out

any entries.

Apply

Click

Apply

to take effect the settings.

Refresh

Click

Refresh

to begin configuring this screen afresh.

Summary of Contents for NGI-M08C4-L2


























































































































































































































































































































Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands

Tripp Lite NGI-M08C4-L2, Owner'S Manual

Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands