Tripp Lite NGI-M08C4-L2 Owner'S Manual Download Page 242

Page: 242 / 313

242

field.

Destination MAC

Configures the destination MAC of the packets that you want to filter.

Mask of

Destination MAC

Configures the bitmap mask of the destination MAC of the packets that

you want to filter.

If the Destination MAC field has been configured and this field is

empty, it means the profile will filter the one MAC configured in

Destination MAC field.

DSCP

Configure the DSCP for the profile.

802.1p

Configures the 802.1p for the profile.

Source IP

Configures the source IP of the packets for the profile.

Mask of Source IP

Configures the bitmap mask of the source IP of the packets for the

profile.

If the Source IP field has been configured and this field is empty, it

means the profile will filter the one IP configured in Source IP field.

Destination IP

Configures the destination IP of the packets for the profile.

Mask of

Destination IP

Configures the bitmap mask of the destination IP of the packets for the

profile.
If the Destination IP field has been configured and this field is empty,

it means the profile will filter the one IP configured in Destination IP

field.

IP Protocol

Configures the IP protocol type. The setting will be used for Source

Application and Destination Application.
TCP:0x06. UDP:0x11.

Source Application Configures the source UDP/TCP ports of the packets for the profile.
Destination

Application

Configures the destination UDP/TCP ports of the packets for the

profile.

Source Interface(s) Configures one or a rage of the source interfaces of the packets for the

profile.

Apply

Click

Apply

to take effect the settings.

Refresh

Click

Refresh

to begin configuring this screen afresh.

Summary of Contents for NGI-M08C4-L2


























































































































































































































































































































Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands

Tripp Lite NGI-M08C4-L2, Owner'S Manual

Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands