Tripp Lite NGI-M08C4-L2 Owner'S Manual Download Page 281

Page: 281 / 313

281

User Name

This field displays the v3 user name.

Group Name

This field displays the group name which the v3 user mapping.

Auth Protocol

These fields display the security level to this v3 user.

Priv Protocol
Rowstatus

This field displays the v3 user row status.

Action

Click

Delete

to remove a v3 user.

9.1.3.3

View Settings

9.1.3.3.1

CLI Configurations

Node

Command

Description

enable

show snmp view

This command displays all snmp v3 view.

enable

configure terminal

This command changes the node to configure

node.

configure snmp view VIEWNAME

STRINGS (included|excluded) To identify the subtree.

configure no snmp view VIEWNAME

STRINGS

This command removes a v3 view from

switch.

9.1.3.3.2

Web Configurations

Parameter

Description

View Settings

View Name

Enter the v3 view name for creating an entry in the SNMPv3 MIB

view table.

Summary of Contents for NGI-M08C4-L2


























































































































































































































































































































Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands

Tripp Lite NGI-M08C4-L2, Owner'S Manual

Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands