Tripp Lite NGI-M08C4-L2 Owner'S Manual Download Page 25

Page: 25 / 313

Unit LEDs

LED

Condition

Status

PWR

Illuminated

Primary power is supplied to switch

Off

Primary power off or failure

RPS

Illuminated

Redundant power is supplied to switch

Off

Redundant power off or failure

ALM

Illuminated

External signal device will be activated through

terminal block ALM when there is any alarm.

Alarm for following conditions



Power lost (primary or secondary)

Abnormal voltage input

Off

No alarm to report

POST

Illuminated

Switch is ready or running

Blinking

Self-testing the device when power On

Off

Switch is not ready

SFP

(9~12)

Illuminated

SFP port link-up

Blinking

Activity (receiving or transmitting data)

Off

Port disconnected or link failed

1000

Illuminated

Port is operating in 1000Mbps speed

Off

Port is operating in 10/100Mbps speed

LNK/ACT

Illuminated

Ethernet link up

Blinking

Activity (receiving or transmitting data)

Off

Port disconnected or link failed

3.4.

USB Port

USB device can be inserted for auto firmware up-gradation. Switch auto-checks the firmware

version present in the USB device and upgrades if newer version of Firmware is present.

For example if you are running with Firmware version 1.0.0.S0 you need to upgrade the

firmware to version 1.0.1.S0 then you need to follow these steps.

Create a folder with model name in USB (eg: NGI-M08C4-L2)

Note: don’t add ‘A’ in folder name.

Insert new firmware file in that folder.

Note:

There should be only one firmware file in the folder. If there is more than one, the

firmware upgrade process will stop.

Plug in USB drive to USB port of NGI-M08C4-L2

Summary of Contents for NGI-M08C4-L2


























































































































































































































































































































Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands

Tripp Lite NGI-M08C4-L2, Owner'S Manual

Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands