Trilithic Three User Manual Download Page 59

Page: 59 / 104

Model Three - Operation Manual

The Maximum

Video and Maximum

Adjacent channel status are

determined by the results of the overall channel plan measurements. Press
the

and

keys to view the Minimum and Maximum Video

channels and levels. Also, if a failure has occurred for the Maximum

Adjacent channel test, the adjacent channels with the greatest variation
are listed.

The Minimum Video, Maximum Video, Minimum

V/A, and Maximum

V/A are tested for all channels in the User Plan. If any channel fails one of
these tests, the Test Result summary indicates a failure

for that test. If

all channels pass one of these tests, the Test Result summary indicates a
pass (check mark) for that test.

A digital (DIGI) type channel is measured
during the Limit test but is not used to
determine Pass or Fail for any of the tests.

Summary of Contents for Three









































































































Search results

Summary of Contents for Three

Reviews:

Brands by name

Popular brands

Trilithic Three, User Manual

Search results

Summary of Contents for Three

Reviews:

Brands by name

Popular brands