Toyota Land Cruiser 2007 Manual Download Page 251 | Manualshive

Page: 251 / 308

background image

289

4. After the tire is lowered completely

to the ground, remove the holding
bracket as shown in the illustration.

When storing the spare tire, put it in
place with the outer side of the wheel
facing up and hook the holding brack-
et as shown in the illustration. Then
secure the tire, taking care that the
tire goes straight up without catching
on any other part, to prevent it from
moving during a collision or sudden
braking.

Check the tire from the side to see
that the tire is stored horizontally.

—Blocking the wheel

2. Block the wheel diagonally op-

posite the flat tire to keep the
vehicle from rolling when it is
jacked up.

When blocking the wheel, place a
wheel block in front of one of the front
wheels or behind one of the rear
wheels.

«
...
249
250
251
252
253
...
»

Summary of Contents for Land Cruiser 2007





















































































































































































































































































































Reviews:

No comments

Related manuals for Land Cruiser 2007

Brand: ABL Pages: 176

Brand: ABL Pages: 94

Brand: CAMPARK Pages: 20

Brand: M7 SPEED Pages: 11

Brand: Metra Electronics Pages: 8

Brand: Hudson Pages: 34

Brand: Jaeger Pages: 13

Brand: Paccar Pages: 63

Brand: Streetwize Pages: 4

Brand: Mopar Pages: 18

Ridesmart KMA-610

Brand: KlipXtreme Pages: 12

Brand: Renault Pages: 3699

2010 Accord Coupe

Brand: Honda Pages: 410

Brand: Green Valley Pages: 17

Brand: Prime Design Pages: 12

Brand: iSimple Pages: 8

Advanced Million Color

Brand: LedGlow Pages: 4

Brand: Audiovox Electronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands