Toyota Land Cruiser 2007 Manual Download Page 113 | Manualshive

Page: 113 / 308

background image

99

4. To remove the convertible seat, press

the buckle release button and allow the
belt to retract completely. The belt will
move freely again and be ready to
work for an adult or older child passen-
ger.

13c569

(C) BOOSTER SEAT INSTALLATION

A booster seat must be used in for-
ward−facing position only.

13c570

Move seat fully back

CAUTION

D

A forward−facing child restraint sys-
tem should be allowed to be
installed on the front passenger
seat only when it is unavoidable.
Always move the seat as far back
as possible even if the front pas-
senger occupant classification indi-
cator light indicates “OFF”, because
the front passenger airbag could in-
flate with considerable speed and
force. Otherwise, the child may be
killed or seriously injured.

«
...
111
112
113
114
115
...
»

Summary of Contents for Land Cruiser 2007





















































































































































































































































































































Reviews:

No comments

Related manuals for Land Cruiser 2007

Brand: Falcon Pages: 8

FRONT HEADLIGHT LENS COVER

Brand: Bimmer Jakes Pages: 4

Brand: Pivot Pages: 4

KO PROPO RTF 2002 ESC

Brand: Tamiya Pages: 2

Brand: GMC Pages: 20

Brand: REVCAMUK Pages: 4

2011 Civic Sedan

Brand: Honda Pages: 5

990E0-54P56-000

Brand: Suzuki Pages: 12

Wireless Handsfree Car Kit

Brand: Wagan Pages: 20

Brand: PEUGEOT Pages: 249

Brand: TATA Motors Pages: 92

Brand: Meta System Pages: 22

Brand: Guidosimplex Pages: 8

Brand: Jaeger Pages: 11

Brand: Honda Pages: 24

BLADE-AL-HK4-EN

Brand: iDataLink Pages: 35

Automobille 2004 Century

Brand: Buick Pages: 12

Brand: GEMINI TECHNOLOGY Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands