Toyota Land Cruiser 2007 Manual Download Page 254 | Manualshive

Page: 254 / 308

background image

292

When connecting a jack handle exten-
sion with another extension and a jack
handle end, use a jack handle to tight-
en the bolts on the joints as shown
in the illustration. When connecting
the jack handle with extension, tight-
en the wing bolt on the jack handle
securely. Make sure the hollow meets
the bolt on any joint when you tighten
the bolts.

NOTICE

Tighten all the joints securely.
Otherwise, the extension may
come off and it may damage
the paint or vehicle body.

—Raising your vehicle

6. After making sure no one is in

the vehicle, raise it high enough
so that the spare tire can be
installed.

Remember you will need more ground
clearance when putting on the spare
tire than when removing the flat tire.

«
...
252
253
254
255
256
...
»

Summary of Contents for Land Cruiser 2007





















































































































































































































































































































Reviews:

No comments

Related manuals for Land Cruiser 2007

Brand: Vintage Air Pages: 28

WirelessAIR 73000EZ

Brand: Air Lift Pages: 12

Brand: travall Pages: 2

Brand: Gacell Pages: 12

Brand: Saab Pages: 9

Brand: Thule Pages: 4

Brand: Westfalia Pages: 10

Brand: Yakima Pages: 28

Brand: Hama Pages: 13

Brand: Reliant Pages: 206

Brand: RAM Pages: 5

T13 Outback Frontal Protection System

Brand: T.J.M. Pages: 18

Brand: Audi Pages: 4

Brand: Hama Pages: 39

Brand: Mazda Pages: 604

Brand: Adaptiv Mini Pages: 4

Brand: Ford Pages: 2

Brand: Toyota Pages: 596

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands